Should CNC machining choose down milling or up milling
2022-09-07
Should CNC machining choose down milling or up milling
(Summary description)The cutting edge of the milling cutter is subjected to an impact load every time it cuts. In order to successfully mill, you must consider the correct contact mode between the cutting edge and the material when cutting in and cutting out. In the milling process, the workpiece is fed in the same or opposite direction as the rotation direction of the milling cutter, which will affect the cutting in and out of milling, and whether to use down milling or up milling.
The cutting edge of the milling cutter is subjected to an impact load every time it cuts. In order to successfully mill, you must consider the correct contact mode between the cutting edge and the material when cutting in and cutting out. In the milling process, the workpiece is fed in the same or opposite direction as the rotation direction of the milling cutter, which will affect the cutting in and out of milling, and whether to use down milling or up milling.
01The golden rule of milling-from thick to thin
When milling, always consider the formation of chips. The decisive factor for chip formation is the position of the milling cutter. We must strive to form thick chips when the cutting edge cuts in and thin chips when the cutting edge cuts out to ensure a stable milling process. Remember the golden rule of milling "from thick to thin" to ensure that the chip thickness is as small as possible when the blade is cut out.
02 Down milling
In down milling, the cutting tool feeds in the direction of rotation. As long as the machine tool, fixture and workpiece permit, down milling is always the preferred method.
In edge down milling, the chip thickness will gradually decrease from the beginning of cutting, and finally reach zero at the end of cutting. This prevents the cutting edge from scratching and rubbing against the surface of the part before participating in the cutting.
A large chip thickness is beneficial, as the cutting force tends to pull the workpiece into the milling cutter, keeping the cutting edge cutting. However, because the milling cutter is easily pulled into the workpiece, the machine tool needs to deal with the table feed gap by eliminating backlash. If the milling cutter is pulled into the workpiece, the feed will increase unexpectedly, which may result in excessive chip thickness and fracture of the cutting edge. In these cases, consider using up milling.
03 up milling
In up-milling, the feed direction of the cutting tool is opposite to the direction of rotation.
The chip thickness gradually increases from zero until the end of cutting. The cutting edge must be forcibly cut in to produce scratching or polishing effects due to friction, high temperature, and frequent contact with the work hardened surface caused by the front cutting edge. All this will shorten the tool life.
The thick chips and higher temperature generated when the cutting edge is cut out will cause high tensile stress, which will shorten the tool life, and the cutting edge will usually be damaged quickly. It can also cause the chips to stick or weld to the cutting edge, which will then carry it to the starting position of the next cut, or cause the cutting edge to break instantaneously.
The cutting force tends to push the milling cutter and the workpiece away from each other, and the radial force tends to lift the workpiece from the table.
When the machining allowance changes significantly, up milling may be more advantageous. When using ceramic inserts to process high-temperature alloys, it is also recommended to use up milling, because ceramics are more sensitive to the impact generated when cutting into the workpiece.
04 Workholding
The feed direction of the tool puts forward different requirements on the workpiece fixture. During up-milling, it should be able to resist lifting force. During down milling, it should be able to resist downforce.
(Summary description)The cutting edge of the milling cutter is subjected to an impact load every time it cuts. In order to successfully mill, you must consider the correct contact mode between the cutting edge and the material when cutting in and cutting out. In the milling process, the workpiece is fed in the same or opposite direction as the rotation direction of the milling cutter, which will affect the cutting in and out of milling, and whether to use down milling or up milling.
The cutting edge of the milling cutter is subjected to an impact load every time it cuts. In order to successfully mill, you must consider the correct contact mode between the cutting edge and the material when cutting in and cutting out. In the milling process, the workpiece is fed in the same or opposite direction as the rotation direction of the milling cutter, which will affect the cutting in and out of milling, and whether to use down milling or up milling.
01The golden rule of milling-from thick to thin
When milling, always consider the formation of chips. The decisive factor for chip formation is the position of the milling cutter. We must strive to form thick chips when the cutting edge cuts in and thin chips when the cutting edge cuts out to ensure a stable milling process. Remember the golden rule of milling "from thick to thin" to ensure that the chip thickness is as small as possible when the blade is cut out.
02 Down milling
In down milling, the cutting tool feeds in the direction of rotation. As long as the machine tool, fixture and workpiece permit, down milling is always the preferred method.
In edge down milling, the chip thickness will gradually decrease from the beginning of cutting, and finally reach zero at the end of cutting. This prevents the cutting edge from scratching and rubbing against the surface of the part before participating in the cutting.
A large chip thickness is beneficial, as the cutting force tends to pull the workpiece into the milling cutter, keeping the cutting edge cutting. However, because the milling cutter is easily pulled into the workpiece, the machine tool needs to deal with the table feed gap by eliminating backlash. If the milling cutter is pulled into the workpiece, the feed will increase unexpectedly, which may result in excessive chip thickness and fracture of the cutting edge. In these cases, consider using up milling.
03 up milling
In up-milling, the feed direction of the cutting tool is opposite to the direction of rotation.
The chip thickness gradually increases from zero until the end of cutting. The cutting edge must be forcibly cut in to produce scratching or polishing effects due to friction, high temperature, and frequent contact with the work hardened surface caused by the front cutting edge. All this will shorten the tool life.
The thick chips and higher temperature generated when the cutting edge is cut out will cause high tensile stress, which will shorten the tool life, and the cutting edge will usually be damaged quickly. It can also cause the chips to stick or weld to the cutting edge, which will then carry it to the starting position of the next cut, or cause the cutting edge to break instantaneously.
The cutting force tends to push the milling cutter and the workpiece away from each other, and the radial force tends to lift the workpiece from the table.
When the machining allowance changes significantly, up milling may be more advantageous. When using ceramic inserts to process high-temperature alloys, it is also recommended to use up milling, because ceramics are more sensitive to the impact generated when cutting into the workpiece.
04 Workholding
The feed direction of the tool puts forward different requirements on the workpiece fixture. During up-milling, it should be able to resist lifting force. During down milling, it should be able to resist downforce.
